Visión nocturna y térmica.

Productos más vistos

Novedades

Visor ATN Day/Night X-Sight-II

Nuevo

PLAZO DE ENTREGA APROXIMADO DE 10 DIAS.

Servicio post venta y garantía oficial. Incluye luz infraroja.

Más detalles

701,65 €

Más

Preparing the Device

Unpacking
  1. Open packaging box, remove X-Sight II and check the contents
  2. Make sure that nothing is missing
  3. Inspect the device for damage to optical surfaces, body, eyecups, operation buttons, etc.
  4. Ensure that all optical surfaces are clean and ready for use

NOTE:
If any accessories are missing or broken contact ATN’s Customer Service.

Image

Installation of Batteries

The X-Sight II will operate on four Lithium AA-type batteries.

NOTE:
We highly recommend using the ATN Power Weapon Kit.  With it you do need any batteries and will have an average of 16hrs of running time.  You will also be able to mount your scope on higher caliber systems since strong recoil will no longer be able to dislodge internal batteries and thereby potentially power down the scope.

Install batteries as follows:

  1. Remove the battery cap by unscrewing it counter clockwise
  2. Insert batteries as shown
  3. Return the battery cap into the housing (screw clockwise until finger tight and the red ring is no longer visible)

Image

Do not over tighten as it will be difficult to remove the next time you replace batteries.

NOTE:
Make sure that the device is turned off before changing the power source.

MicroSD, USB and HDMI Ports

The device is equipped with microSD Card, microUSB and microHDMI ports. You can find them under the cap near the battery compartment.
To open the cap unscrew it counterclockwise.

Image

NOTE:
Make sure that the device is turned off before inserting the card into the slot.

  1. A new card should be formatted before
  2. Insert microSD card as shown
  3. To lock when inserting card in the slot, push it with a thin object (a small coin, paper clip, toothpick, etc.)
  4. Return the cap into the housing (screw clockwise until finger tight)

Image

NOTE:
There is only one correct direction to insert the microSD Card.
Do not force the card into the slot as it may damage both the scope and the card itself.

To remove the microSD Card from the slot, push it in using the same thin object. When it pops up a few millimeters, it can be pulled with your fingers or tweezers.
Image
NOTE :
If you are going to record video then microSD Card should be of Class 10 (10 mb/sec) or faster and have capacity from 4 to 64 Gb.

How to Update the Firmware

Before operating your device please update the firmware to the latest version.
To receive notification of new firmware updates, please register your device on our website (you’ll receive an email letting you when new firmware becomes available).

To update the new firmware you will need a microSD Card and batteries that are fully charged.

NOTE:
In the event of a power failure during an update the device may crash corrupting its system files and will need to be sent back to the ATN factory for service.
It is important not to use an additional source of power during a firmware update!

Update the new firmware as follows:

  1. Download the *.bin file and copy to your microSD Card – root directory
  2. Insert the card into the scope
  3. Turn ON the scope
  4. In the “Firmware Update” dialog box select “Yes” to start the update
  5. When the update counter reaches “100%” the device will automatically restart
  6. Once the device is powered up it will enter self configuration mode
  7. After completing it will automatically restart and will be ready for use
  8. The motion Sensing platform will be configured when first turned on

NOTE
If the device does not restart within 30 seconds, remove and re-insert the batteries and power-up the device.

Image

ON / OFF

To TURN ON the device press and hold the POWER button until you see the ATN splash screen.

To TURN OFF the device press and hold the POWER button, until the dialog box “Shut down the device?” appears. Choose “Yes” to turn off the device.

Image

Using the Keypad

The KEYPAD is programmed to be used in two different ways:

  • Short and Quick Taps – used for most functions and to get around the menu;
  • Press and Hold – designed to be used on the following situations — ON/OFF, ZOOM, SHORTCUT MENU.

NOTE
Using the LEFT or RIGHT buttons in the menu allows you to quickly return to the previous screen

Image

Focusing

DIOPTER ADJUSTMENT
By rotating the Diopter Adjustment Ring you will achieve optimal sharpness for your vision. Look through the eyepiece while focusing on the reticle on the screen.
Do not take the rubber cap off the objective lens.

Image

NOTE:
You should not need to re-adjust the Diopter Adjustment unless another user with different vision than yourself will be using the scope.

DISTANCE FOCUS
Remove the cap from the objective lens and rotate the Adjustment Dial as necessary to achieve proper focus at various distances.

Image

Mounting

Mount your X-Sight II as follows:

  1. Slightly loosen the fixing screws on the 7/8″ weaver mount built into the scope
  2. Place the scope on the weaver rail of the firearm
  3. Tighten the fixing screws

NOTE:
The fixing screws may need to be re-tightened after continuous shooting.

Image

NOTE:
We recommend using “Loctite” to make sure the screws will not loosen during shooting.

Compass Calibration

When the compass need to be calibrated the word “CAL” appears instead of the Compass Scale.  To calibrate you should rotate the device in three axis as pictured below.

Image

NOTE:
After calibrating the device please remember that the compass will work best when holding the X-Sight parallel to the ground.

Another possible abbreviations:

  • ERR — an error was detected (you may need to restart the device or recalibrate the compass);
  • SMF — your device is under a Strong Magnetic Field (move away from the Magnetic Field);
  • UPD — your firmware needs to be updated.

Interface

Home Screen

First screen you’ll see after switching on the device is Home Screen. It consist of Scales, Status Bar icons and different Information Widgets.

Image

SCALES
E-Compass Scale shows yaw angle based on e-Magnetometer data.
Roll Scale shows rifle cant based on the internal 3D Gyroscope.
Pitch Scale shows rifle inclination based on the internal 3D Gyroscope.

STATUS BAR
Displays information about the current state of the system.

  • Inactive icons become invisible, so you see only the important information at the moment:
  • Battery — appears when energy level is low;
  • SD Card — shows the presence or absence (red icon) of memory card;
  • Shooting Solution, Bluetooth, GPS and WiFi — shows when the function is enabled or disabled.

WIDGETS
They are interface elements which provide quick access to useful information. There are several types of widgets:

  • icons without value — used to display modes (Photo and Video Modes);
  • only numerical value (Detailed Roll and Pitch Values);
  • icons with a numerical value;
  • Photo Preview (appears in the bottom of the home screen, after the photo was taken).

Image

Display widgets can be disabled from the System Menu.

To get to the System Menu you should click on the CENTER button center from Home Screen and access the Shortcut Carousel.
Then select the wrench icon with RIGHT or LEFT buttons right-left and push the CENTER button center to enter the menu.
Select Display tab with RIGHT button right and choose subcategory Display Widgets with the DOWN button down .

Image

Main Operations

2-2-1
ZOOM LEVEL
By pressing and holding the UP or DOWN button  up-down on the keypad you will be able to Zoom IN and OUT.
Current Zoom Level is displayed at the Zoom widget on the Home Screen.
NOTE:
When the device is setup for the first time you need to configure the lense option in the pop-up window before zooming.

While using the Smart Shooting Solution your reticle can be displaced from the center point of the screen. When zooming in it will move to the center.

2-2-2
TAKING PHOTOS
Press the LEFT button left to TAKE A PHOTO.
Depending on the selected mode you will make one or several photos. You can choose from various photo modes in the System Menu.

2-2-3
VIDEO RECORDING
By pressing the RIGHT button right you will be able to RECORD VIDEO (if you use Normal Mode) or START RAV (if Recoil Activated Video mode is on).
You can switch the video recording modes in the System Menu.

NOTE:
Your recording will automatically stop when the memory card is full or the battery is out of power.

2-2-4
SHORTCUT CAROUSEL
The CENTER button center opens the menu and close it down when pressed again.

The Carousel is your access to a number of Shortcuts that allows you quick access to your scope’s features.

Just click on the CENTER button center from Home Screen to access the Carousel.

Buttons highlighted in Red are the only ones that active at a particular shortcut.

Image

Movement between the items is carried out using the LEFT & RIGHT buttons right-left , except the group of ON/OFF switches (WiFi, GPS, Bluetooth, Shooting Solution, RAV).
You should use the UP & DOWN buttons up-down between switches.
To turn ON or OFF a particular switch you should click the CENTER button center while having the switch selected. Example — WiFi.

  • 2-3-2
    EXIT
    Exit Carousel.
  • 2
    NIGHT MODE
    Switch between Day and Night Mode.
    Options such as color palette and other settings for Night Mode can be changed in the System Menu.
  • 2-3-4
    RANGEFINDER
    Activates Smart Rangefinder feature. If the Smart Shooting Solution is ON then the range that is found using the Rangefinder will be automatically used to adjust your point of impact (shift reticle to adjust for drop).
  • 3-2
    DISTANCE ENTRY
    Manualy input or adjust the distance to the target to be used by the Smart Shooting Solution.
  • 2-3-5
    GALLERY
    Gives you access to the library of Images and Videos that are stored on your scope’s SD Card.
  • 3-3
    ENVIRONMENT
    Allows for input of various environmental data to improve ballistic correction, such as wind speed and direction.
  • 2-3-8
    SYSTEM MENU
    Allows for access to various system options and adjustments.The grouped switches consist of the next items:
  • 2-3-6
    WIFI module
  • 2-3-7
    GPS module
  • 0
    BLUETOOTH module
  • 3-4
    SMART SHOOTING SOLUTION
  • 3-5
    RAV (Recoil Activated Video)
Using System Menu

To enter the System Menu you should open Shortcut Carousel with CENTER button  center  and select the wrench icon with RIGHT or LEFT buttons right-left  . Then push CENTER button  center  to enter the menu.

Image
The System Menu consist of Tab Bar at the top of the screen, list of subcategories in the center and Help Information at the bottom.

Image

On the left side of the Tab Bar you will find the Exit (with arrow icon). Pressing it with CENTER button center will bring you back to the Home Screen. Movement between the tabs is carried out using the LEFT and RIGHT buttons right-left . Each tab includes subcategories.

To select a particular subcategory you should use the UP and DOWN buttons up-down and press CENTER button center .

Image

To change a particular value you should follow next few steps. Select the subcategory you needed with the UP or DOWN buttons up-down .

Image
Press the Center button center to select a particular value (once selected it will turns red).
Image
Change the value with the UP and DOWN buttons up-down .
Image
To select a new value press CENTER button center to confirm the change.

Functions

Night Vision

To switch between Day and Night Mode you should choose NIGHT MODE in Shortcuts. 

Image

Shortcuts allows you quick access to the Carousel that contains quick access to your scope’s features. Just click on the CENTER button center to access the Carousel.
Buttons highlighted in Red are the only ones that active at a particular shortcut.

Movement between the items is carried out using the LEFT & RIGHT buttons  right-left .

NOTE:
Remember that turning on Night Mode during daylight will not harm your device, however you may not be able to see anything due to the image being too bright.

You can choose preferred Сolor Theme or adjust the Light Sensitivity in the System Menu (NIight Vision section).
To enter the System Menu you should open Shortcut Carousel with CENTER button  center  and select the wrench icon with RIGHT or LEFT buttons right-left .
Then push CENTER button  center  to enter the menu.
Image

Choose a Night Vision in Tab Menu. Movement between the tabs is carried out using the LEFT and RIGHT buttons  right-left  .
To switch between Green and Black&White modes follow next few steps. Select Color Theme subcategory in Night Vision Tab by pressing UP and DOWN buttons up-down .

Then Press the Center button  center  to select a particular value (once selected it will turns red). And choose Green or Black&White mode, confirm it by pressing Center button center  .
Choosen category will be aviable from Shortcut Menu.
Image  Image

NOTE:
Light Sensitivity does not change when changing color modes.

Photo Modes

Press the LEFT button left while staying at Home Screen to TAKE A PHOTO.

You must have a microSD card inserted in the device for these features to work. All files will be stored on the microSD card.
Depending on the the selected mode you will make one or several photos. You can choose from various photo modes in the System Menu.

To enter the System Menu you should open Shortcut Carousel with CENTER button center and select the wrench icon with RIGHT or LEFT buttons right-left .
Then push CENTER button center to enter the menu.

Image

There are three photo modes to choose from. Switching between modes is done in the System Menu from Photo/Video tab, subcategory Photo Mode.
Use UP or DOWN buttons up-down to switch between modes. Press the Center button center to select a particular value (once selected it will turns red).

3-1-2
NORMAL
This default mode allows you to take one photo at a time.

3-1-3
TIME LAPSE
Time-lapse is where the device takes a sequence of images of a subject with an interval of time between each image.
The interval and the number of photos taken can be changed in the System Menu.

Image

To make changes choose a Photo/Video Tab in System Menu, then use UP or DOWN buttons  up-down  to select Time Lapse Settings. Press the Center button  center  to enter the mode settings. While you are in this mode, the Time Lapse widget appears.

photo_modes_time_lapse

3-1-6
BURST
Burst mode captures a series of photos.
You can select the best image of the group or arrange them in a sequence to study the transitions in detail.
The number of the photos taken can be changed in the System Menu. While you are in this mode, the Burst widget appears.
photo_modes_burst
Regardless of which mode you are using the preview appears after a photograph is taken on the bottom of the screen for several seconds.
Image

Recoil Activated Video

Recoil Activated Video (patent pending) offers a unique approach to taking videos with your Smart Sight.
RAV offers you an ability to take a video of before, during and after your shot has been fired.

rav

Perfect for those hunting moments when getting your target far outweighs the importance of remembering to turn on your video record. Simply set your RAV to ON, set your parameters and anytime your Pull the Trigger (RAV is activated from the recoil of your weapon) the sight will record a number of seconds before your shot, and a number of seconds after.
All conveniently organized as one continuous video.

Press the RIGHT button right to Start Video recording. Press RIGHT button right again to stop Video recording.

NOTE:
It may best to turn OFF the Microphone in conditions of extreme wind.

You can turn on the microphone and switch the quality of the video in the System Settings (Photo/Video tab).

Image

To enter the System Menu you should open Shortcut Carousel with CENTER button center and select the wrench icon with RIGHT or LEFT buttons right-left . Then push CENTER button center to enter the menu.

You must have a microSD card inserted in the device for these features to work. All files will be stored on the microSD card. Recorded videos you can find in the Gallery on your device.

The scope allows you to record videos in two modes.

3-2-6
NORMAL
The default mode. While recording the Counter widget and Time Stamp appear.

rav_normal

Image
RECOIL ACTIVATED VIDEO (RAV)
When you set your video record to RAV mode (from Shortcut Menu), the system buffers everything your scope sees.

rav

While you are in this mode, the RAV widget appears and then after starting record the Time Counter appears.

rav_2
When a shot is fired and your scope experiences recoil (some airguns may not provide enough recoil for RAV to be activated) the scope will record video prior to the shot being taken, the moment of, and a some time after. Exact settings may be adjusted in the System Menu.

Image

Rangefinder

Using the Smart Range Finder you will quickly be able to estimate the distance to your target as long as you have reasonable knowledge of the size of your target.
NOTE:
Once the distance is measured the value will be automatically integrated into your Smart Shooting Solution.

RANGEFINDER
To use select the Flag Icon from the Shortcut Carousel.

Image

Pressing the CENTER button   center  will take you to the Main Screen of Rangefinder feature.

Image

To measure the distance, follow the next steps:

  1. Put the arrow-mark on the top of the target and press the CENTER button center , wait for the scope to take the readings (it will take a number of readings so try to keep your weapon steady)
  2. Put the arrow-mark under the target and press the CENTER button center
  3. If satisfied with the value press the LEFT button left to go back to the Home Screen or repeat steps 1 and 2 if necessary.

Image

NOTE:
During the measurement process, you can zoom in and out using standard buttons (UP and DOWN)

If the Target Height is incorrect you can change it:

  • press the RIGHT button right to enter the Menu
  • сhoose one of the presets or input the height manually
  • accept the height with CENTER button center and go back to the Main Screen

Image
DISTANCE ENTRY
Allows you to input or correct the distance manually. To launch you should choose it in the Shortcuts.
Image
Change distance value using UP and DOWN buttons  up-down . To accept the new distance press CENTER button center  .
Image

Zeroing

To Zero in your scope you will need to go to the Profile/Zero section of the System Menu.

Image
To enter the System Menu you should open Shortcut Carousel with CENTER button  center  and select the wrench icon with RIGHT or LEFT buttons right-left .
Then push CENTER button  center   to enter the menu.

Before you begin Zeroing process you will need to either create a new Profile or utilize an existing one. We recommend to create a new one to start understand the process better.
Image

Profiles are primarily used in order to utilize your scope on various weapons.  This way when moving your scope from one gun to the next you can simply select the Profile that you have already created for this gun.  Another reason to use multiple profiles is to be able to zero in the scope on the same gun but at different ranges. For example one Profile may be called AR 50 yards and another AR 200 yards.  Allowing you to create two separate profiles to better fine tune your shooting solutions for both shorter and longer range shooting.

To zero your rifle with the ATN device you should follow few next steps.
Image

Image

Find Profiles/Zero tab in the System Menu with RIGHT or LEFT buttons right-left . Select Zero Reticle item and hit CENTER buttoncenter .

Image

Aim and fire at the target (preferably bullseye) while keeping the reticle on the bullseye. If possible keep the weapon from moving as much as possible. After the shot has penetrated the target, move your reticle to the point of impact and press the CENTER button  center  .

NOTE:
Although you may not need more then one shot to Zero in your scope we do recommend that you repeat the process several times to make sure that you truly Zeroed in. As you gain experience in Zeroing in your scope it should take you no time at all to Zero it in the future.

Image

NOTE:
It may be helpful to Zoom in while Zeroing in your scope. This will not effect your results.

When finished Select Save & Exit in the menu.  Congrats, you have Zeroed in your scope!

NOTE:
Before zeroing scope you must choose correct lens type for your scope.
This lets the system know which Scope you are actually using (example: X-Sight II 3-14 or 5-20).

Smart Shooting Solution

Smart Shooting Solution is a fully integrated Ballistics Calculator that enables your scope to seamlessly adjust its point of impact. The first step in utilizing this function requires you to enter all relevant information into the Profile that is being used.

Image

NOTE:
If you do not know all or part this info (example: Initial Velocity) we recommend that you contact the manufacturer of the ammunition
or/and the weapon that you are using. Generally this info should be found on the manufacturer’s website.

Once your profile has been setup you are ready to activate the Shooting Solution on your sight. Open the Carousel and locate the following set of Icons.

Image

You will need to scroll with UP and DOWN buttons  up-down   to find the Shooting Solution bullseye icon and if it is off (indicated by a diagonal line running through the icon), you will need to turn it on by hitting CENTER button center   while having the icon selected. You will see the diagonal line disappear and a Smart Shooting Solution icon will appear in the top right corner of the screen.

Image

Profiles which are not in use are situated in the Other section. You can use an existing profile or create up to 6 new user profiles.

Image

Image

To edit a Profile you should select it (highlighted in red), press CENTER button center and choose the action you want to be done: Load, Copy (Duplicate) or Delete the selected profile.

ENVIRONMENT

Image

There are a number of Environmentals that may be entered to increase the precision of your shots.

Image

Wind:
Generally speaking Wind strengths and direction are by far the most important of the group, especially during medium to heavy winds. We highly recommend that if you plan to shoot at ranges of over 300 yards you take wind readings and enter the information into your sight. Both wind speed and wind direction are needed if you plan to make accurate shots. You can enter the information through the Environment short cut or you can utilize your mobile device (running the Obsidian App with a Wifi connection to your scope) whichever you find easier.

Humidity & Temperature:
Humidity and Temperature must also be entered through the Environment short cut or by utilizing your mobile device.

Barometer Pressure & Altitude:
Both Pressure and Altitude will be set automatically using your sight’s internal sensors.

Other Data Collected:
The angle of your scope as in relations to your target is also noted and the Smart Shooting Solution takes the information into its calculations.

RANGING IN ON YOUR TARGET

Clearly the number one priority to achieve accuracy in long range shooting is to know the range to your target.
The Smart Shooting Solution will make your adjustments for you but only after you have entered the range to your target.
Your sight offers several ways to accomplish this task.

RANGEFINDER

Select the Flag Icon from the Shortcut Carousel.

Image

Pressing the CENTER button center will take you to the Main Screen of Rangefinder feature.

Image

To measure the distance, follow the next steps:

  1. Put the arrow-mark on the top of the target and press the CENTER button center , wait for the scope to take the readings
    (it will take a number of readings so try to keep your weapon steady)
  2. Put the arrow-mark under the target and press the CENTER button center
  3. If satisfied with the value press the LEFT button left  to go back to the Home Screen or repeat steps 1 and 2 if necessary.

Image

NOTE:
During the measurement process, you can zoom in and out using standard buttons (UP and DOWN).
While using Smart Shooting Solution your reticle can be displaced from the center point of the screen. Then during Zoom In action it will move to a center.

If the Target Height is incorrect you can change it:

  • press the RIGHT button right to enter the Menu
  • сhoose one of the presets or input the height manually
  • accept the height with CENTER button center and go back to the Main Screen

Image

DISTANCE ENTRY

If you are using other means such as Laser Range Finder you may enter the distance manually using the Distance Entry shortcut.

Image

Change distance value using UP and DOWN buttons up-down . To accept the new distance press CENTER button center .

Reticle Style Adjustment

You can manage reticle style in the System Menu (Display section).

To enter the System Menu you should open Shortcut Carousel with CENTER button center and select the wrench icon with RIGHT or LEFT buttons right-left .

Then push CENTER button center to enter the menu.

Choose a Display in Tab Menu. Movement between the tabs is carried out using the LEFT and RIGHT buttons right-left .

3-7-1

To change the Reticle Shape press the CENTER button center .

3-7-2

You can choose prefered shape depends on your purpose. Use keyboard arrows to switch between shapes.
To accept appropriate shape of the reticle press the CENTER button center .

3-7-3

You can chage Reticle Color depending on circumstances.

3-7-4

Movement between the colors is carried out using the LEFT and RIGHT buttons right-left . Then press CENTER button center to accept color you need.

3-7-5

System Menu

Night Vision

Image
COLOR THEME — the color of Night Mode (Green or Black & White).  There is NO difference in light gain from Green to B&W.

LIGHT SENSITIVITY — can be set to Low, Medium or High.  At high your frame rate will be 7.5 per seconds.  You will experience more light gain but at the expense of lower frame rate.  We recommend Medium setting for most uses.

Photo/Video

Image
PHOTO MODE — includes Single (capture a single photo), Time Lapse (series of photos at timed intervals) and Burst (up to 10 photos in one second) modes.

BURST COUNT — ammount of photos in one second (2 – 10).

TIME LAPSE SETTINGS

  • Total Photos — ammount of photos in series (2 – 10).
  • Frame Interval — length of the interval (2 – 15 sec).

MICROPHONE — sound recording (ON/OFF).

VIDEO QUALITY — can be 1080p30 or 720p60.

RECOIL ACTIVATED VIDEO

  • Record Before Shot — the time before pulling a trigger (5 – 30 sec).
  • Record After Shot — the time after pulling a trigger (5 – 30 sec).

FORMAT SD CARD — after you choose this subcategory you’ll see a pop-up window asking you about formatting.

Display

Image
SCREEN BRIGHTNESS — 1-5 with 1 being the dimmest and 5 the brightest.  It is recommended that you use the brightest setting during the day for optimal performance.

DISPLAY WIDGETS — allows you to disable several widgets (Minimal/Extended)

SLEEP MODE
Sleep mode is activated when your scope is not in use for a set period of time (example: 1 –  60min).  During sleep mode the display and some of the sensors will be inactive. To get out of Sleep mode and get back to normal operations just physically move the device or press any of the buttons.

  • Mode — allows you to switch the mode (ON/OFF)
  • Hibernation Time — can be 1 – 60 min

RETICLE STYLE

  • Shape — you can choose the shape of your Reticle.
  • Color — the color of your Reticle.
Profiles/Zero

Image
CURRENT

  • Zero Reticle — allows to enter zeroing mode.
  • Drag Function — the flight path and characteristics of bullets devided into types (G1 – G8, GL)
  • Ballistic Coefficient — measure of bullet’s ability to overcome air resistance in flight.
  • Bullet Weight — influences the kinetic energy of the bullet downrange.
  • Initial Velocity — is the velocity of the projectile as soon as it leaves the barrel.
  • Zero Range — is the range that a firearm is sighted at.
  • Sight Height — is referring to the distance between the center of the optics and the center of the barrel.

OTHER

  • Profile Name — list of existing profiles.
  • Create New Profile —allows to create up to 6 profiles.
Settings

menu_5_settings
UNITS — can be Metric or Standard system.

DATA AND TIME

  • Clock Source — allows you to choose different types of source to improve the accuracy (Manual, WiFi or GPS).
  • Date Format — can be YYYY-MM-DD, MM-DD-YYYY, DD-MM-YYYY.
  • Time Format —  form of stating the time (24-hour or 12-hour).
  • Data — enter the date.
  • Time — enter the time.
  • Time Zone — allows you to choose a geographical region with standard time.

WIFI — values are not changeable.

  • SSID
  • Password
  • MAC Adress

RECORD GEO-TAGGING — adding geographical identification to your videos (ON/OFF).

LENSE TYPE — to make all features work correctly you need to choose the type of your lense ( Example: 3x stands for 3–14x and 5x stands for 5–20x ).

ZOOM — allows you to choose different types of zoom (Standard, Extended). Extended Zoom will give an electronic zoom of 10x your optical Zoom.
Example: 3–14x in Extended mode becomes 3–30x .  However, we would like to caution you that you will begin to see considerable pixelation at such a zoom.

RESTORE FACTORY SETTINGS — allows to reset all the settings to default.

FIRMWARE VERSION — allows you to learn on the firmware version currently running on your sight.
We recommend that you register your product on our home page (www.atncorp.com) in order to make sure that you are getting emails when new firmware versions become available.
We are constantly working on new features, functions, and improvements that we provide to you free of charge via firmware upgrades.

Servicing

Warnings and Сautions
  • Always remember to turn off the device when it is not in use. If you do not plan on using it for a period of more than 10 days, you should remove the batteries.
  • Do not disassemble, drop, open, crush, bend, deform, puncture, shred, microwave, incinerate, paint or insert foreign objects: it will void your warranty.
  • Keep Lens Cap on when not in use.
  • Avoid contact with dust, steam, and gas.
  • This product contains natural rubber latex which may cause allergic reactions.
  • The scope is a precision electro-optical instrument and must be handled carefully.
  • Do not scratch the external lens surfaces or touch them with your fingers.

CAUTION
Failure to follow these safety instructions could result in damage to the device!

Mobile Applications

Android Application

iOS Application

Accesorios

13 otros productos de la misma categoría: